Camber
The inward or outward tilt of the tire, seen from the front. Top tilted in is negative; top tilted out is positive. Too much either way wears one edge of the tire. Uneven camber side to side can cause a pull.
Alignments on a Hunter machine at our shop on Concord Rd.
Alignments starting at $89.99. Trucks and large SUVs start at $98.50.
Free brake & suspension diagnosis
¡Se habla español!

An alignment sets the angles of your wheels so the tires sit flat on the road, point straight ahead and track together. Every vehicle has a factory spec range for each angle. On our Hunter machine we measure each angle, compare it to spec, and adjust what your vehicle allows to be adjusted.
The inward or outward tilt of the tire, seen from the front. Top tilted in is negative; top tilted out is positive. Too much either way wears one edge of the tire. Uneven camber side to side can cause a pull.
The forward or backward tilt of the steering axis, seen from the side. Positive caster helps the steering wheel return to center and keeps the vehicle stable at speed. Uneven caster side to side can cause a pull. By itself it has little effect on tire wear.
Whether the fronts of the tires point in toward each other (toe-in) or out (toe-out), seen from above. Toe out of spec scrubs the tread and is the biggest cause of alignment-related tire wear, often a feathered edge. It's set by adjusting the tie rods.
The direction the rear axle points compared to the vehicle's centerline. If it's off, the vehicle 'dog-tracks' and the steering wheel sits crooked even when you're driving straight. A 4-wheel alignment takes it into account.
A vibration at highway speed is usually tire balance, a bent wheel or a worn part, not alignment. Bring it in and we'll find out. Diagnosis for brakes and suspension is free.
Pick your type of suspension, then tap a part to see what it does and how wear on it throws off your alignment. Drawings are simplified, not to scale.
Parts
Where the strut bolts to the steering knuckle makes a big difference in how camber gets adjusted.
The knuckle bolts to a bracket on the strut with two bolts. On some vehicles one hole is slotted from the factory, or the upper bolt is an eccentric (cam) bolt. On others the holes are round, and an aftermarket camber bolt kit (a smaller bolt with an offset cam) can add some adjustment. Turning the cam pushes the top of the knuckle in or out, which tilts the wheel.
The strut slides into the knuckle and one pinch bolt clamps it. There's usually little or no factory camber adjustment at this joint. If camber is out on this design, the fix may be an aftermarket part like an adjustable or offset top mount, a camber plate, or an offset bolt or bushing made for that vehicle, or it may mean a bent part needs replacing.
Movement is exaggerated so you can see it. A cam bolt usually gives a limited range, often around a degree or two depending on the vehicle. It can't fix a bent strut, knuckle or arm. If camber is way out, something is usually bent or worn.
Aline Front End & Brakes does wheel alignments and front-end work in Beaumont, TX. We set alignments on a Hunter machine at our shop at 3490 Concord Rd.
Alignments start at $89.99. Trucks and large SUVs start at $98.50. Call (409) 892-7813 for a quote on your vehicle.
We work on light-duty vehicles only. We also work on older vehicles.
We are open Monday through Friday, 8 AM to 5 PM, and closed Saturday and Sunday.

Alignments start at $89.99. Trucks and large SUVs start at $98.50. Call (409) 892-7813 for a quote on your vehicle.
We set alignments on a Hunter machine at our shop at 3490 Concord Rd, Beaumont, TX.
Yes. We work on older vehicles, and we work on light-duty vehicles only.
Monday through Friday, 8 AM to 5 PM. We are closed Saturday and Sunday. Call (409) 892-7813. We are at 3490 Concord Rd, Beaumont, TX 77703.
It's a good idea. New tires on an alignment that's out can start wearing unevenly right away. Call (409) 892-7813 and we'll check it.
Usually not. Vibrations are more often tire balance, a bent wheel or worn parts. Diagnosis for brakes and suspension is free, so bring it in.
Yes. We align lifted trucks and Jeeps. We work on light-duty vehicles only.
Some suspensions, like many single-bolt strut designs and solid axles, have little or no factory camber adjustment. Aftermarket parts can add adjustment on many of them. If camber is way out, something may be bent or worn.